Preparing an ADR shipping document: which data are mandatory?

Preparing an ADR shipping document: which data are mandatory?

Preparing an ADR waybill requires more than just listing the shipper, receiver and goods being transported. For road transport of hazardous substances the transport document must contain specific information, such as the UN number, the correct shipping name, hazard class, packing group and quantity. These obligations are set out in ADR 5.4.1.

An incorrectly completed ADR waybill can lead to problems during an inspection by the Inspectorate for Environment and Transport (ILT). Moreover, accurate information is important for drivers and emergency services when an incident occurs during transport.

In this article we explain which data are mandatory, the order in which they must be listed, and which additional regulations apply to special transports.

When is an ADR waybill required?

When transporting dangerous goods to which the ADR documentation requirements apply, an ADR transport document must be present.

This document contains information about the dangerous goods being transported and must be available during transport.

A separate form titled ‘ADR waybill’ is not required. ADR data may, for example, be included in a regular waybill or CMR waybill, provided all prescribed information is present and legible.

Even for transport under the 1000-point rule of ADR 1.1.3.6, an ADR transport document remains mandatory.

For certain exemptions, including exclusively correctly offered Limited Quantities (LQ), the normal ADR documentation requirements do not apply. Other transport documents may still be required under general transport legislation.

What information must be on an ADR waybill?

According to ADR 5.4.1.1.1, the applicable data must be listed for each hazardous substance or hazardous item.

The main mandatory components are:

  1. UN number: The four‑digit identification number of the dangerous goods, preceded by the letters UN. For example UN 1203 for gasoline.
  1. Correct shipping name: The official shipping name from table A of the ADR. A commercial product name is not sufficient. For certain collection designations, such as N.E.G. mentions, the technical name must also be included in parentheses.
  1. Hazard class and additional hazards: The number of the prescribed hazard label. When additional hazards apply, the relevant label numbers are listed in parentheses. Specific rules apply for class 1 and class 7.
  1. Packing group: If assigned, packing group I, II or III is indicated. This denotes the packaging-related hazard level. Not every hazardous substance has a packing group.
  1. Number and description of the packages: State how many packages are being transported and what type of packaging, e.g., 10 steel drums or 4 cardboard boxes.
  1. Total quantity of dangerous goods: The total amount per distinct UN number, shipping name and, if applicable, packing group. Depending on the goods this is expressed in liters, gross mass or net mass.
  1. Name and address of the shipper: The company that acts as the shipper under the ADR.
  1. Name and address of the consignee: The company or person to whom the goods are delivered.
  1. Any mandatory statements: When a special regulation or agreement requires it, the relevant statement must be included.
  1. Tunnel restriction code: If the route passes through a tunnel subject to ADR restrictions, the applicable tunnel restriction code from column 15 of table A must be listed. The code is in capital letters and in parentheses, e.g., (D/E).

In what order must the ADR data be listed?

The ADR stipulates that the following components be presented in a fixed order:

UN number → correct transport name → hazard class → packaging group → tunnel code

These data must appear consecutively, without other information in between, unless the ADR specifies otherwise.

A correct example from ADR 5.4.1.1.1 is:

UN 1098 ALLYLALCOHOL, 6.1 (3), I, (C/D)

Here:

  • UN 1098 is the UN number.
  • ALLYLALCOHOL is the correct transport name.
  • 6.1 is the primary hazard.
  • (3) is the additional hazard.
  • I is the packaging group.
  • (C/D) is the tunnel restriction code.

The number of packages, quantities and address details may be placed elsewhere on the transport document.

The data must clearly relate to the specific hazardous goods.

ADR waybill example: what does a correct entry look like?

Suppose a company transports ten drums each containing 20 liters of a hazardous substance that is correctly classified as UN 1098 ALLYLALCOHOL.

An example of the ADR entry is:

UN 1098 ALLYLALCOHOL, 6.1 (3), I, (C/D)

Additionally, the following are listed:

  • Number of packages: 10 drums.
  • Total quantity: 200 liters.
  • Name and address of the sender.
  • Name and address of the recipient.

This example shows how the standard data can be combined on a transport document. For the actual shipment, any additional regulations must also be checked.

The tunnel restriction code does not need to be listed according to ADR 5.4.1.1.1 when it is known in advance that the transport will not pass through a tunnel with restrictions for hazardous goods.

What information is required under the 1000-point scheme?

The 1000-point scheme of ADR 1.1.3.6 provides, under certain conditions, an exemption from part of the ADR regulations. However, the obligation to prepare a transport document remains.

When applying this scheme, the transport document must also state, for each transport category, the total amount of hazardous goods and the calculated value according to ADR 1.1.3.6.

An example:

Transport category Quantity Factor Calculation
2 100 liters 3 300 points
3 200 liters 1 200 points
Total 500 points

This information is added to the other mandatory ADR transport information. The full load must meet the exemption conditions.

Read also: How does the ADR 1000‑point calculation work?

Special entries for waste and empty packages

For certain transports, additional entries are required.

Dangerous waste

According to ADR 5.4.1.1.3, for hazardous waste materials, except radioactive waste, the word WASTE must be placed before the correct transport name, unless it is already part of the transport name.

An example is:

UN 1230 WASTE METHANOL, 3 (6.1), II, (D/E)

For certain waste mixtures, additional provisions exist.

Empty, uncleaned containers

Empty containers and tanks containing hazardous residues can still fall under ADR.

Depending on the type of containment, the designation ‘EMPTY, UNCLEANED’ or another prescribed description must be used.

Environmentally hazardous substances

When a substance meets the applicable criteria for environmental hazard, the designation ‘ENVIRONMENTALLY HAZARDOUS’ may be mandatory. An exception applies for UN 3077 and UN 3082.

In which language must an ADR consignment note be prepared?

According to ADR 5.4.1.4.1, transport information must be prepared in an official language of the country of dispatch.

If this is not English, French or German, the information must also be available in one of these three languages, unless applicable national or bilateral agreements apply.

For transport that takes place solely in the Netherlands, a Dutch-language document may be used. According to the ILT this also applies to transport between the Netherlands and Belgium.

For other international transport from the Netherlands, it is advisable to include the required ADR information also in English, French or German.

Who is responsible for a correct ADR consignment note?

The sender must ensure that the carrier has the correct information about the dangerous goods. This obligation is stipulated in ADR 1.4.2.1.

The carrier must, among other things, verify that the prescribed information and documents are present before transport begins.

A driver must have access to the required documents during transport.

An incorrect classification or a missing packaging group can therefore have consequences for multiple parties involved. It is important to carefully check the data before departure.

Common mistakes when preparing an ADR consignment note

In practice, various mistakes occur:

  • Using a product name instead of the official ADR transport name.
  • Listing the UN number without the letters UN.
  • Forgetting an additional hazard or packaging group.
  • Not indicating the number of packages or the quantity correctly.
  • Using an incorrect tunnel restriction code.
  • Not listing the quantities per transport category under the 1000-point scheme.
  • Forgetting the mandatory waste declaration.
  • Copying outdated classification data from a safety data sheet.

These errors can be prevented by using a fixed control procedure and up-to-date ADR classification data.

ADR safety advisor for transport companies

Checking ADR transport documents is one of the important focus points in the work of an ADR safety advisor.

ADR Advisors supports independent drivers and small transport companies in complying with ADR regulations, including procedures for transport documents and the annual ADR report.

View our services for own drivers

View our services for small businesses

Arrange today your external ADR safety advisor

Do you want to organize your ADR obligations properly without hiring a safety advisor?
ADR Safety Advisors offers an affordable solution for in-house drivers and small transport companies.

Secret Link